Latest Specification HDMI & Displayport Cables INSTOCK!!!
Complete Range of HDMI Audio & Video Distribution
Wired or Wireless Networking Solutions and Installations
Power Over Ethernet - POE Network Switches & CCTV Cabling
previous arrow
next arrow
Slider

Transmitter | HDBiTT Matrix HDMI IP Extender over Network Switches with Infrared | Up to 16 Sources 16xN

R2639.00

Availability: In stock

Social Interaction....

Transmitter | HDBiTT Matrix HDMI IP Extender over Network Switches with Infrared | Up to 16 Sources 16xN | Unlimited Displays

Note that this is the Transmitter ONLY and must be used with Receivers as below. You can use 16 Transmitters and Unlimited Receivers depending on your network size:

Receiver | HDBiTT Matrix HDMI IP Extender over Network Switches with Infrared | Up to 16 Sources 16xN

Transmitter | HDBiTT Matrix HDMI IP Extender over Network Switches with Infrared | Up to 16 Sources 16xN Transmitter | HDBiTT Matrix HDMI IP Extender over Network Switches with Infrared | Up to 16 Sources 16xN

INSTALLATION REQUIREMENTS

  • HDMI source devices (computer graphics card, Playstation, HD or CCTV Monitoring equipment, Broadcasting station via HDMI, DSTV Explora etc) – Up to 16 Devices (Needs 16 Transmitters)
  • Displays or projectors with HDMI port (Unlimited Displays supported depending on your network size)
  • 100Mbit/s minimum Ethernet LAN switch with IGMP and IGMP snooping functions.
  • UTP/STP cat5e/6 cable (STP Recommended)
IP and MAC address setting

Each Transmitter and Receiver is equipped with a HTTP server. You can change system IP and MAC Address via a browser. Before building network matrix, the IP and MAC Address of TX and RX must be set and all TX and RX units must have different IP addresses AND different MAC Addresses. The principle is that, all the RX and TX in the same network matrix must be in the same network segment, the IP and MAC Addresses. Transmitters and Receivers have a default IP address. TX is 192.168.168.55, RX is 192.168.168.56 which can be customized for your network via a web browser. If any changes needed or device not visible on network  press the system reset button for 5 seconds {the small hole beside of HDMI port) to restore IP and MAC to default factory setting.

SPECIFICATION
IMPORTANT SAFETY INSTRUCTIONS
  • Do not mix up transmitter TX and receiver RX before installation.
  • Do not mix up IR blaster extension cable and IR receiver extension cable before installation.
  • Do not plug and unplug IR blaster extension cable and IR receiver extension cable with power on.
  • Use Supplied DC5V power supply only. Please make sure specification matched if using adapters not supplied by us.
PACKAGE CONTENTS
  • Transmitter
  • DC 5V 1amp
  • IR eye (to Source Devices)
  • User Manual
Group Choosing | Choosing which source must output to which display

1.Button usage instructions

  • Short press: Press to set IGMP Display group e.g if Transmitter on Selection 1 and a Receiver on selection 1 then the HDTV / Projector on receiver will display Source 1. Product switches automatically to the corresponding display group after pressed.
  • Long press:Press and keep 3 seconds to reset the product, only for software.It will not restore system specification to factory setting.

Transmitter | HDBiTT Matrix HDMI IP Extender over Network Switches with Infrared | Up to 16 Sources 16xN

2.Front display Selection

  • When Receiver and Transmitter display is the same value, it builds corresponding IGMP Display groups. Receiver will output the same signal with the matched Transmitter. One RX can support 16 TX source signals at the most.

The Switches below are commonly used with these Matrix Extenders

26 Port Rack Mountable Gigabit Network Switch | 2 SFP Ports for Transceiver Modules | OEM

Wireless Transmission of HDMI over LONG Ranges

This product has been tested with the Wireless Long Range Beams and HDMI over Powerline Devices below for long ranges via Home or Office Powerlines or Wireless Outdoor Installations. Range on Outdoor Installation will depend on line of site and has been tested up to 1km.

200Mbps Fast Ethernet over PowerLine Network Adapter | Tenda

Ubiquiti NanoBeam Outdoor Wireless Network Range Extender up to 10km NBE-M5-16

Gigabit Ethernet Network over Powerline Adapter | Tenda

Weight0.9 kg

Customers' review

5 stars 0 0 %
4 stars 0 0 %
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

Reviews

There are no reviews yet.

Be the first to review “Transmitter | HDBiTT Matrix HDMI IP Extender over Network Switches with Infrared | Up to 16 Sources 16xN”